Communication
control command |
2000H |
0001H:forward running
( chạy thuận )
0002H:reverse running
( chạy ngược )
0003H:forward jogging
( chạy Jog thuận )
0004H:reverse jogging
( chạy Jog nghịch )
0005H:stop
( dừng)
0006H:coast to stop (emergency stop)
0007H:fault reset
( xoá lỗi )
0008H:jogging stop |
W ( write) |
The address of the
communication n
setting value |
2001H |
Communication setting frequency(0~Fmax(unit:
0.01Hz))
( tần số cài đặt ) |
W ( write) |
|
2002H |
PID reference, range(0~1000, 1000 corresponds
to100.0% ) |
W ( write) |
|
2003H |
PID feedback, range(0~1000, 1000 corresponds
to100.0% ) |
W ( write) |
|
2004H |
Torque setting value (-3000~3000, 1000
corresponds to the 100.0% of the rated current
of the motor) |
W ( write) |
|
2005H |
The upper limit frequency setting during forward
rotation(0~Fmax(unit: 0.01Hz)) |
W ( write) |
|
2006H |
The upper limit frequency setting during reverse
rotation(0~Fmax(unit: 0.01Hz)) |
W ( write) |
|
2007H |
The upper limit torque of electromotion torque
(0~3000, 1000 corresponds to the 100.0% of the
rated current of the motor) |
W ( write) |
|
2008H |
The upper limit torque of braking torque
(0~3000, 1000 corresponds to the 100.0% of the
rated current of the motor |
W ( write) |
|
2009H |
Special control command word
Bit0~1:=00:motor 1 =01:motor 2
=10:motor 3 =11:motor 4
Bit2:=1 torque control prohibit
=0: torque control prohibit invalid
Bit3: =1 power consumption clear
=0: no power consumption clear
Bit4: =1 pre-exciting
=0: pre-exciting prohibition
Bit5: =1 DC braking
=0: DC braking prohibition |
W ( write) |
|
200AH |
Virtual input terminal command, range: 0x000~0x1FF |
W ( write) |
|
200BH |
Virtual input terminal command, range:0x00~0x0F |
W ( write) |
|
200CH |
Voltage setting value(special for V/F separation)
(0~1000, 1000 corresponds to the 100.0% of the
rated voltage of the motor) |
W ( write) |
|
200DH |
Voltage setting value(special for V/F separation)
(0~1000, 1000 corresponds to the 100.0% of the
rated voltage of the motor) |
W ( write) |
|
200EH |
AO output setting 2
(-1000~1000, 1000 corresponds to 100.0% ) |
W ( write) |
| SW 1 of the inverter |
2100H |
0001H:forward running
( xem trạng thái chạy thuận )
0002H:reverse running
( xem trạng thái chạy nghịch )
0003H:stop
( xem trạng thái dừng )
0004H:fault
0005H: POFF state
0006H: pre-exciting state |
R(read) |
| SW 1 of the inverter |
2101H |
Bit0: =0:bus voltage is not established
=1:bus voltage is established
Bi1~2:=00:motor 1 =01:motor 2
=10:motor 3 =11:motor 4
Bit3: =0:asynchronous motor
=1:synchronous motor
Bit4:=0:pre-alarm without overload
=1:overload pre-alarm
Bit5~ Bit6:=00: keypad control
=01:terminal control
=10:communication control |
R(read) |
| Fault code of the inverter |
2102H |
See the fault type instruction |
R(read) |
| Identifying code of the inverter |
2103H |
GD20—–0x0106 |
R(read) |
| Operation frequency |
3000H |
Range: 0.00Hz~P00.03
( xem tần số hoạt động ) |
R(read) |
| Setting frequency |
3001H |
Range: 0.00Hz~P00.03 |
R(read) |
| Bus voltage |
3002H |
Range: 0~2000V |
R(read) |
| Output voltage |
3003H |
Range: 0~1200V
( xem điện áp ngõ ra ) |
R(read) |
| Output current |
3004H |
Range: 0.0~3000.0A
( xem dòng điện làm việc ) |
R(read) |
| Operation speed |
3005H |
Range: 0~65535RPM
( xem tốc độ hoạt động ) |
R(read) |
| Output power |
3006H |
Range: -300.0~300.0% |
R(read) |
| Output torque |
3007H |
Range: -250.0~250.0% |
R(read) |
| Close loop setting |
3008H |
Range: -100.0%~100.0% |
|
| Close loop feedback |
3009H |
Range: -100.0%~100.0% |
R(read) |
| PID setting |
3008H |
-100.0~100.0% (unit: 0.1%) |
R(read) |
| PID feedback |
3009H |
-100.0~100.0% (unit: 0.1% |
R(read) |
| Input IO |
300AH |
000~1FF |
R(read) |
| Input IO |
300BH |
000~1FF |
R(read) |
| AI 1 |
300CH |
Range: 0.00~10.00V |
R(read) |
| AI 2 |
300DH |
Range: 0.00~10.00V |
R(read) |
| AI 3 |
300EH |
Range: 0.00~10.00V |
R(read) |
| AI 4 |
300FH |
Range: 0.00~10.00V |
R(read) |